Outdoor Furniture

Modern 2×4 Planter Bench: Plans, Cut List and 3D Model

Our designDesigned by DIY Outdoor Builds and checked board by board in a 3D model built from real lumber sizes. We have not built this one yet, so measure as you go.

A 7 ft outdoor bench with a planter box at each end, built entirely from sixteen 8 ft 2×4s and exterior screws. Every board was modelled and checked in 3D, so the cut list, the cutting diagram and the step drawings all match.

Want to build this?

  1. Check what you need6 materials · 7 tools
  2. Download the plans5 files
  3. Follow the steps8 steps
  4. Share your versionAbout ten minutes

About this design

This bench puts a planter box at each end of a long slatted seat, so herbs, grasses or flowers grow right beside you. It is built entirely from standard 2×4 lumber and exterior screws, with no special joints, which makes it a good first furniture build. We designed it as a 3D model using real lumber sizes and checked that no two boards overlap and that every board is fixed to another; we have not built this exact bench ourselves yet, so measure as you go.

Each planter is a square box 18 in (46 cm) on each side, built from five rows of 2×4s laid on edge and screwed to four corner posts inside. A bottom of three slats on two cleats holds the soil, and a frame of four mitred caps finishes the top. Between the planters, two seat rails rest on ledger boards screwed to the planter walls, three cross supports keep the rails apart and stop the seat from sagging, and four seat slats finish the seat flush with the top of the planter walls.

The whole bench is 84 in (2.13 m) long, which seats three adults, and the seat is 17½ in (44 cm) high, a comfortable height for an outdoor bench. All 77 boards come from sixteen 8 ft 2×4s. The parts are lettered A to K in the cut list, the cutting diagram and the step drawings, so you can mark each piece as you cut it.

The bench was modelled board by board in a parametric CAD program, with every board at its actual size rather than its nominal size: a 2×4 is 1½ × 3½ in (38 × 89 mm), not 2 × 4 in. A script then checks three things before any drawing or cut list is produced: that no two boards occupy the same space, that every board touches and can be screwed to at least one other, and that each board in the model is exactly the size listed in the cut list. The cut list, the cutting diagram and the step drawings on this page all come from that same model, so they cannot disagree with each other.

What a model cannot check is your lumber. Boards from the store vary slightly in width and are rarely perfectly straight, so measure the real gap before cutting the parts that fit between others, such as the side wall boards and the cross supports.

How it is designed

  • Overall length: 84 in (2.13 m)
  • Depth: 18 in (46 cm)
  • Height at the planter caps: 19 in (48 cm)
  • Seat height: 17½ in (44 cm)
  • Seat length between the planters: 48 in (1.22 m)
  • Planter inside, at the soil: 15 × 15 in (38 × 38 cm)
  • Soil depth: 12½ in (32 cm)
  • Soil per planter: About 1.6 cu ft (About 46 L)
  • Every part is 2×4, 1½ × 3½ in actual (38 × 89 mm); parts are lettered A to K in the cut list, the cutting diagram and the drawings.

Materials

ItemQtyNotes
2×4 boards, 8 ft (2.4 m), pressure-treated or cedar16Exactly what the cutting diagram uses; buy one spare if the boards are not straight
Exterior screws 3 in (76 mm)About 300Four per wall board, plus the bottoms, caps and seat
Landscape fabric3 × 6 ft (0.9 × 1.8 m)Lines the walls and bottom of both planters
Potting mixAbout 3.3 cu ft (92 L)Two bags of 2 cu ft or two of 50 L

Tools

  • Mitre saw (or a circular saw and a speed square)
  • Drill/driver with a countersink bit
  • Tape measure, pencil and speed square
  • Two clamps
  • Spirit level
  • Sandpaper or a sanding block
  • Safety glasses, hearing protection and a dust mask

Cut list

PartQtyLengthSectionNotes
A · Front/back wall board2018 in (457 mm)2×4 (1½ × 3½ in / 38 × 89 mm)Pressure-treated or cedar
B · Side wall board2015 in (381 mm)2×4 (1½ × 3½ in / 38 × 89 mm)Pressure-treated or cedar
C · Corner post817½ in (444 mm)2×4 (1½ × 3½ in / 38 × 89 mm)Pressure-treated or cedar
D · Bottom cleat412 in (305 mm)2×4 (1½ × 3½ in / 38 × 89 mm)Pressure-treated or cedar
E · Bottom slat615 in (381 mm)2×4 (1½ × 3½ in / 38 × 89 mm)Pressure-treated or cedar
F · Top cap818 in (457 mm)2×4 (1½ × 3½ in / 38 × 89 mm)Pressure-treated or cedar. 45° mitre at both ends; length is the long edge
G · Seat ledger216 in (406 mm)2×4 (1½ × 3½ in / 38 × 89 mm)Pressure-treated or cedar
H · Seat rail248 in (1219 mm)2×4 (1½ × 3½ in / 38 × 89 mm)Pressure-treated or cedar
J · Cross support313 in (330 mm)2×4 (1½ × 3½ in / 38 × 89 mm)Pressure-treated or cedar
K · Seat slat448 in (1219 mm)2×4 (1½ × 3½ in / 38 × 89 mm)Pressure-treated or cedar

The cut list comes straight from the 3D model, which is checked so that no two boards overlap, every board is joined to another and every board is exactly the length listed. Measure the real gaps before cutting the parts that fit between others.

Cutting diagram: which parts to cut from each board (16 8 ft 2×4 boards)
Cutting diagram for 16 8 ft 2×4 boards: parts by letter, ⅛ in (3 mm) for each saw cut, and ½ in (13 mm) trimmed off one end of every board to square it.

How to build it

  1. 1Cut and mark all the parts

    Cut the 77 parts from the sixteen boards following the cutting diagram, longest parts first: the 48 in seat rails (H) and seat slats (K), then the 18 in wall boards (A) and caps (F), and so on. Square one end of every board before you measure. Set a stop block on the saw for each length so repeated parts are identical, and write the part letter on each piece in pencil. Cut the eight caps (F) last, with a 45° mitre at both ends so the long edge is 18 in (457 mm).

  2. 2Build the first planter box

    Stand two corner posts (C) upright and screw the bottom front wall board (A) across them, flush with the post bottoms, with the posts set 1½ in (38 mm) in from each end of the board; that space is where the side boards fit. Repeat on the back. Then fit the side wall boards (B) between the front and back boards and screw them to the posts. Work up row by row, five rows in all, checking that the box is square by measuring the diagonals after the second row. Build the second box the same way.

    Step 1: two planter boxes of five rows of 2×4 wall boards on four corner posts, parts A, B and C labelled
  3. 3Add the planter bottoms

    Inside each box, screw a bottom cleat (D) to the front wall and another to the back wall, between the corner posts, with their tops 3½ in (89 mm) above the bottom of the box, level with the top of the first row. Lay three bottom slats (E) front to back across the cleats, with gaps of about ¾ in (19 mm) between them for drainage, and screw each slat to the cleats.

    Step 2: bottom cleats D and three bottom slats E inside each planter box
  4. 4Set the planters in place

    Move both boxes to where the bench will stand, on firm and level ground, with their inner side walls exactly 48 in (1.22 m) apart and parallel. Check with a long straight board and the level that the two boxes are at the same height; pack under a low corner with a paver or a flat stone rather than shims that rot.

  5. 5Fit the ledgers and the seat frame

    Screw a seat ledger (G) flat against the inner side wall of each box, 11 in (28 cm) above the ground and centred front to back, so the seat frame can rest on it. Lay the two seat rails (H) on edge on the ledgers, 1 in (25 mm) in from the front and back, and screw each rail down into the ledgers and through the box walls. Fit the three cross supports (J) between the rails, one at each end against the box walls and one in the middle, and screw through the rails into their ends.

    Step 3: seat ledgers G on the planter walls, seat rails H and cross supports J between the boxes
  6. 6Screw down the seat slats

    Lay the four seat slats (K) flat across the frame, the outer two flush with the front and back of the planters and the middle two spaced evenly, which gives gaps of about 1⅓ in (34 mm). The tops of the slats should be flush with the top of the planter walls. Pre-drill and fix each slat with two screws into each cross support, six per slat.

    Step 4: four seat slats K screwed across the seat frame between the planters
  7. 7Cap the planters

    Lay the four mitred caps (F) flat on top of each planter, outer edges flush with the walls, so the mitres meet at the corners. Dry-fit all four before you fix any; if a mitre gaps, trim the longest cap slightly. Screw the caps down into the wall boards and the corner posts, and drive one screw across each corner through the mitre to pull the joint tight.

    Step 5: four mitred top caps F on each planter box
  8. 8Line, finish and plant

    Sand the seat, the caps and any rough edges. Staple landscape fabric to the inside walls and over the bottom slats of each planter, leaving the drainage gaps covered but not sealed. Oil or stain the outside if you like, but leave the inside of the planters untreated. Fill each planter with potting mix to about 1 in (25 mm) below the caps and plant.

Plans and drawings

The 3D model and drawings of this design, free to download for your own build. Open STEP in Fusion 360, FreeCAD or most CAD programs; STL and OBJ in SketchUp (with an importer), Blender or a 3D viewer; DXF in any 2D CAD program. Units are inches.

  • 3D model (STEP), for Fusion 360, FreeCAD and most CAD programsSTEP · 1.2 MB Download
  • 3D model (STL), for SketchUp, Blender and 3D viewersSTL · 45 KB Download
  • 3D model (OBJ)OBJ · 25 KB Download
  • 2D drawing: front, side and top views (DXF)DXF · 131 KB Download
  • Cutting diagram: which parts to cut from each boardSVG · 15 KB Download

Use and upkeep

  • Each planter holds about 1.6 cu ft (46 L) of soil, 12½ in (32 cm) deep: enough for herbs, compact grasses, lavender, trailing flowers or a small evergreen. Avoid plants that grow tall and floppy right beside the seat, and plants with thorns. In a sunny spot, a mix of thyme, oregano and trailing rosemary smells good every time someone sits down. Water more often than beds in the ground, because small planters dry out quickly in summer.
  • Pressure-treated pine is the cheapest choice and lasts well outdoors; modern treatments are generally considered fine for ornamental planting, and the landscape fabric keeps the soil off the wood. If you plan to grow herbs or vegetables and prefer untreated wood, cedar, larch or another naturally rot-resistant wood works well. It costs more, but it also looks better and weathers to an even grey.
  • Check the screws after the first season, oil the seat once a year if you want to keep its colour, and refresh the top layer of potting mix each spring.

Our notes if you build one

  • Choose the straightest boards for the seat rails and seat slats; slight bows matter less in the short wall boards.
  • Cut and label all the parts before you assemble anything. With 77 parts, the letters save a lot of measuring later.
  • Drive the wall-board screws into the corner posts, not into the end grain of the next board; posts hold screws far better.
  • Building the planters out of square. If the diagonals differ, the caps will not close at the mitres and the seat will not sit flat.
  • Setting the planters more or less than 48 in apart. The seat rails and slats are cut to that gap, so check it at both front and back before you fix the ledgers.
  • Leaving out the middle cross support. A 48 in 2×4 laid flat bends noticeably under a person; supported in the middle it is firm.
  • To change the seat length, change only the seat rails (H) and seat slats (K); everything else stays the same. Above about 60 in (1.5 m) between the planters, add a second middle cross support. For a lower seat, remove one row of wall boards from each planter and shorten the corner posts by 3½ in (89 mm); the seat frame then sits one row lower and the seat drops to 14 in (36 cm), which suits children. The downloadable model can be changed the same way in any CAD program before you cut.

About this design: designed and modelled by DIY Outdoor Builds; the text was drafted with AI assistance and checked against the model (see our editorial policy). Design, drawings and 3D files © DIY Outdoor Builds: free to download and build for your own use, please do not republish the files. We have not built this exact design yet.

Building work can be dangerous and may need a permit. Check local rules and use a qualified professional for electrical, gas and structural work.

Built something like this?

Share your own version with your photos, measurements and what you changed.

Share your version

More projects like this

All projects

Guides for similar projects

All guides